Considerations of hydraulic tube fittings

  In the hydraulic system, both the metal pipe fitting, hose fitting, or are prone to leakage problems. For card sets of pipe joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the pipe ends in good condition and the extent of compression Hydraulic tube fittings  nut, but also eliminate the pipeline force. For flared fittings, mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated.  
  Pipeline installation: hydraulic tube fitting  to try to avoid the heat radiation and cooling water temperature is too high or too low spray and other place, conflict occurs when you install, you should make a small tube bassoon, low-pressure pipe so that the high-pressure pipe; pipe cross each other can not be contact should be separated by a certain distance. Installation Notes: moving or still in the pipeline are not excessive bending, can not bend at the roots, moved to the extreme position when the pipeline must not pull too tight, should be more relaxed; try to avoid torsional deformation of the pipe; pipe as far as possible away from heat radiating member, the necessary insulation board fashion.

hydraulic fittings profiles and leak prevention

hydraulic fittings in the hydraulic system, the connecting member and the pressure tubing pressure tubing between. hydraulic fittings and the difference between the ordinary pipe joint largest and most significant difference is that the hydraulic pressure is larger staggering, hydraulic oil pipe suddenly burst impact force is great. hydraulic hose fittings can not be replaced by an ordinary dedicated connector, because the hydraulic are can withstand a lot of stress. Quick-change connectors, one is with a one-way valve, one is without a check valve. Application with check valve, check valve and the gas source is connected to the end, when you disconnect the check valve closes automatically when you turn on the activity side thimble-way valve is opened. Is the use of self-locking ball is embedded in the groove, hydraulic flange fittings the locking balls from "tapered cylindrical ---" sleeves. Pipe joints to prevent leakage in the hydraulic system, whether it is a metal fitting, or the hose connector is prone to leakage problems. For card sets of pipe joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the pipe ends in good condition and the extent of compression ferrule nut, but also eliminate the pipeline force. For flared fittings, mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated.

Hydraulic tube fittings classification and disclosure process

Hydraulic tube fittings in the hydraulic system, the connecting member and the pressure tubing pressure tubing between. Hydraulic tube fittings classification: Hydraulic hose, sleeve type fittings, quick joints. Hydraulic tube fittings can not be used to replace ordinary dedicated connector, because the hydraulic are can withstand a lot of stress. Quick-change connectors, one is with a one-way valve, one is without a check valve. Application with check valve, check valve and the gas Hydraulic tube fittings is connected to the end, when you disconnect the check valve closes automatically when you turn on the activity side thimble-way valve is opened. In the hydraulic system, both the metal pipe fitting, hose fitting, or are prone to leakage problems. For card sets of pipe joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the hydraulic tube fitting ends in good condition and the extent of compression ferrule nut, but also eliminate the pipeline force. For flared fittings, mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated.

installation and considerations of hydraulic tube fittings

Hydraulic tube fittings installation Notes: moving or still in the pipeline are not excessive bending, can not bend at the roots, moved to the extreme position when the pipeline must not pull too tight, should be more relaxed; try to avoid torsional deformation of the pipe; pipe as far as possible away from heat radiating member, the necessary insulation board fashion. Hydraulic tube fittings  pipeline installation: Hydraulic tube fittings to try to avoid the heat radiation and cooling water temperature is too high or too low spray and other place, conflict occurs when you install, you should make a small tube bassoon, low-pressure hydraulic tube fittings so that the high-pressure pipe; pipe cross each other can not be contact should be separated by a certain distance. In the hydraulic system, both the metal pipe hydraulic tube fittings, hose fitting, or are prone to leakage problems. For card sets of hydraulic tube fitting joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the pipe ends in good condition and the extent of compression ferrule nut, but also eliminate the pipeline force. For flared fittings, mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated.

hydraulic tube fittings Introduction

  hydraulic tube fittings is in addition to the power source, a control section, the application of elements outside the executive body of the hydraulic system, the other part. For example, filters, air-cooled, liquid level gauge, thermometer and more. Commonly used in the press; engineering machinery, dump truck, etc. Hydraulic tube fittings commonly used in self-unloading trucks, hydraulic lifting device has an associated loading and digging equipment, steel, metallurgy and mining. hydraulic tube fittings , air-cooled, level gauges, thermometers, directional control valves, pressure control valves, throttle valves, pressure gauges, level gauges, filters, coolers, fittings, tubing, seals belong hydraulic tube fittings. Hydraulic tube fittings. Hydraulic line fittings, hydraulic valve, tee, end straight nuts over. Articulated. Valve fittings, cylinders joints and the like. Hydraulic cylinders, cylinders, hydraulic valves, hydraulic pumps, hydraulic station for machine tools on.Connectors are indispensable electronic device components, observe current flow along the path, you will always find one or more connectors.

hydraulic tube fittings installed

hydraulic tube fittings in the hydraulic system, the connecting member and the pressure tubing pressure tubing between. The most common technique of hydraulic pipe surface rust treatment handpiece used widely used in the hydraulic fittings industry. After this process the Hydraulic tube fittings  metal parts, the appearance looks more shiny, pretty, and corrosion resistance capabilities are greatly improved over the general galvanized parts, performance has been greatly improved. hydraulic tube fittings tube length as needed by sawing or special pipe cutting machines and other equipment off when installing pipe hydraulic tube fitting , and definitely not with a melting off (such as flame cutting) or wheel cutting; removing the pipe ends and outside round burrs, metal chips and dirt; remove pipe fittings anti-rust agents and dirt; but also to ensure that the tube roundness. hydraulic tube fittings , air-cooled, level gauges, thermometers, directional control valves, pressure control valves, throttle valves, pressure gauges, level gauges, filters, coolers, fittings, tubing, seals belong hydraulic fittings.

Hydraulic tube fittings leak prevention

In the hydraulic system, both the metal pipe fitting, hose fitting, or are prone to leakage problems. For card sets of pipe joints, mostly due to the pipeline by a larger force or impact, so that the card sleeve loose or pipe end surface deformation caused by leaks, you should check whether the card sets out of round, edge or without defects, whether the pipe ends in good condition and the extent of compression ferrule nut, but also eliminate the pipeline force. For flared hydraulic adapter fittings , mostly due to excessive flaring, substandard quality requirements or repeatedly demolished, resulting in flaring deformation or cracks caused by leaks, then you can be re-flared front amputated. If you use a male and female cone top pressure seal, which is mostly due to the two cone leak damage, is available on the cone grinders for grinding. In some with "о" or outer-ring seal on the end face of the occasion, the leakage following reasons: "о" ring deformation caused by bsp fittings or leakage; "о" ring assembly is not in place, so that the two-plane connection when the pressure is uneven or "о" ring is cut cause leakage; "о" ring is not compacted, less elastic deformation caused by leakage; "о" mouth-ring groove just too deep and cause leaks. In this regard, the need to re-select the same diameter and cross-sectional thick "о" rings can also be sealed with a flat opening slot stop cutting or grinding to reduce the groove depth mouth only to make "о" rings are sufficiently resilient deformation. For use oil sheet, wool felt, soft steel board, combination gasket sealant joints or pipe leaks, no matter what the material is, you should first check the seals for damage, deformation, aging and rough through the large, etc. and then take the appropriate measures. Hose in a npt fittings  or stationary, and can not be bent excessively, can not bend at the base, at least 1.5 times the start of the bending diameter; Hose moved to the extreme position not pull too tight, should be more relaxed; Try to avoid the hose twisting deformation; Hose as far away from the heat radiating member, fashion necessary insulation board; Avoid hose external damage, such as the use of the term with the friction surface of the member; If the hose weight caused excessive deformation, should support members.